Swirl ceiling texture12/28/2023 However, the removal contractor/builder needs to be trained to Cat B (non licensed asbestos training).Īccording to the HSE’S guide, they state:. ” Work with textured decorative coatings will not normally be licensable work, as work with this material will usually not meet the conditions in the definition of licensable work in regulation 2(1).” Hse Managing and working with asbestos L143 It is classed as non-licensable work, in the HSE’s website in their L143 guide on managing and working with asbestos:. The removal work falls within exemptions to the HSE’s licensing requirements. If it is confirmed that there is asbestos in Artex textured coating, and you wish to go ahead with repair work or removal, then a licensed contractor won’t be required. The Laboratory will confirm whether the Artex contains asbestos or not. They will be able to safely take a sample and have it tested in an independent laboratory. You should first seek the advice of a professional Asbestos Surveyor. If you are planning on repairing or removing Artex textured coatings from ceilings or walls in your home. How do you know if your Artex ceiling contains asbestos? The danger comes when inhaling asbestos fibres that are in the Artex as they cause a number of deadly diseases, including the lung disease asbestosis, a cancer of the lining of the lungs called pleural mesothelioma, and cancer of the lining of the abdomen peritoneal mesothelioma. It is only when older Artex textured coatings are removed or damaged that there is a potential health risk from asbestos. It can be painted over with regular emulsion paint. No drilling holes, hammering nails into it and so on. The asbestos in Artex poses no risk at all if left undisturbed. If you are in any doubt about when the textured coating was applied, then have it tested for asbestos.Īsbestos in Artex – stippled textured coating on wall However, it’s worth noting that Artex textured coatings manufactured after the asbestos ban in 1992 shouldn’t contain any chrysotile.īut it’s wise to always have the Artex textured coating tested for the presence of asbestos. There is therefore a risk of asbestos exposure, but only when the Artex is being drilled, sanded or removed. Up until the mid-1980s, Artex was made with white asbestos (chrysotile) to help strengthen it.Īrtex that was manufactured before 1992 when asbestos was banned in Artex may contain chrysotile (white) asbestos. So is asbestos in Artex harmful? Does Artex contain Asbestos all the time? This results in a poor finish, which has harmed it’s popularity.Īnother issue is that Artex is extremely difficult to remove from ceilings, which puts people off from using it. It has decline over the years because when carrying out repair jobs, it’s impossible to match up the pattern exactly. The product is still sold and used, although it doesn’t contain asbestos anymore. Artex Asbestos CeilingsĪrtex-textured ceilings are not as popular as they once were. Don't worry about too much water, you can easily pour it off or it dries pretty quickly, but not to the point where you cannot use it! I also made 2 separate batches for the same wall.Asbestos in artex ceilings – swirl pattern artex ceilingĪrtex was used a lot throughout the 1970’s, mainly on ceilings but also on interior walls. By the way, I used a paint mixer in my drill to stir it up. So I'm going back over previous repairs using more of this! Good luck. It really helped to avoid clumps, make the compound stick where it didn't want to. After I applied my compound, I sprayed some of this on the area and then used my brush. It helps! I had also purchased the spray on texture that comes in several forms. I also had a cup of warm water that I used to apply to the wall before I scraped it and then again when I repaired it. I also had a similar small artistic brush in case I had to maintain the pattern near the moulding, corners of wall or floor. To get the texture right, I then used an old 2 1/2" paint brush that was stiff from not being cleaned correctly. I used a small hand-held plaster trowel to apply the compound in areas where it needed extra fill. IMPORTANT: THE SCRAPING OFF SHOULD MAINTAIN THE DIRECTION OF THE TEXTURE AS IT HELPS TO GUIDE REPAIR. I used a straight edged razor and a hand-held planer to remove the terrible previous repairs. It wasn't quite gritty enough, so I grabbed some sandy-type soil and sifted it in my kitchen. I bought the "sand" mix-in from Home Depot.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |